shopping cart empty
Kiba42's Product Reviews
Sort:
18650 Battery Sleeve PVC Heat Shrinkable Tube Wrap (50-Pack)
18650 Battery Sleeve PVC Heat Shrinkable Tube Wrap (50-Pack)

Avatar
Kiba42
Member

VERIFIED OWNER
  • JoinedApr 2016
  • Posts 376
  • Reviews 34
  • Kudos146
Overall   (4.7)
› Quality
› Value
PROS
Excellent fit, thickness
CONS
None
Can't find any cons with these, must have for any vaper
Reviewed on Was this review helpful to you? Yes / No
Authentic 316L Stainless Steel Heating Wire for RBA
Authentic 316L Stainless Steel Heating Wire for RBA

Avatar
Kiba42
Member

VERIFIED OWNER
  • JoinedApr 2016
  • Posts 376
  • Reviews 34
  • Kudos146
Overall   (5.0)
› Quality
› Value
PROS
A+
CONS
None
This wire is amazing, if you want an exact TFR for it get a csv for 24 awg 316L from steam engine and it works flawlessly in TC. The wire itself is super clean, with no bends or kinks or anything. Flavor is outstanding, I'd reccommend this to anyone and I don't say that a lot.
Reviewed on Was this review helpful to you? Yes / No
Coil Master Styled V3 6-in-1 E-Cigarette Wire Coil Winder
Coil Master Styled V3 6-in-1 E-Cigarette Wire Coil Winder

Avatar
Kiba42
Member

VERIFIED OWNER
  • JoinedApr 2016
  • Posts 376
  • Reviews 34
  • Kudos146
Overall   (4.5)
› Quality
› Value
PROS
1:1 to original v3
CONS
-squeaky threads -no slot -small holes
I had left a few pieces to my original cm jig, like the cap with the hole in it (most important part) and 2 of my rods, somewhere and got this as a replacement for those parts, all of them fit with my original and work the same. only issue is the holes are smaller (i'll probably dril them) and its missing the slot, but I always just held big wires with my finger anyways. a friend has the v4 one from here with the slot and holder, but I got this one under his recommendation that the quality was a bit better, after using it i'd agree.
Reviewed on Was this review helpful to you? Yes / No
SXK Hadaly Styled RDA Rebuildable Dripping Atomizer
SXK Hadaly Styled RDA Rebuildable Dripping Atomizer

Avatar
Kiba42
Member

VERIFIED OWNER
  • JoinedApr 2016
  • Posts 376
  • Reviews 34
  • Kudos146
Overall   (4.0)
› Quality
› Value
PROS
Machining is acceptable, good tolerances on all the other parts Excellent for squonking Easy to use
CONS
The tolerances on the insulator made it hard to get the cap on, had to sand it down some Covered in machine oil Tight o-rings
As stated in the pros/cons, I got this clean by taking it to bits & scrubbing all the parts quite a bit with toothbrush and dish soap. After I put it back together I noticed the tolerances on the peek insulator made it difficult to put the cap on, fixed this by running a bit of sandpaper along the inside of the cap, and on the back of the insulator. After that I discovered the o-rings were too tight but I already had sku 2019300 for the narda, which makes a perfect fit with this and the top cap. Other than that it's excellent, build quality is a actually better than the original, (I had an early authentic one where the air holes didn't line up and were slightly obstructed by the insulator as well) this one is much better imo, and it's a great squonk atty. One of the best along with the narda.
Reviewed on Was this review helpful to you? Yes / No
Protective Stainless Steel Ring for Atomizers
Protective Stainless Steel Ring for Atomizers

Avatar
Kiba42
Member

VERIFIED OWNER
  • JoinedApr 2016
  • Posts 376
  • Reviews 34
  • Kudos146
Overall   (4.2)
› Quality
› Value
PROS
Excellent machining Good fit for 22 mm Works well on dripper/gen
CONS
Will block a/f on rta's
As stated in the pros/cons Ita best if used with a dripper or a gen. But the machining was excellent and I liked that it is SS.
Reviewed on Was this review helpful to you? Yes / No