Wylie's Product Reviews
Sort:

Avatar
Wylie
Member

VERIFIED OWNER
  • JoinedMay 2013
  • Posts 5920
  • Reviews 78
  • Kudos3848
Overall   (3.5)
› Quality
› Value
1 of 3 people found the following review helpful
PROS
conductive metal
CONS
Needs more space for batteries
I'll just post a pic in the discussions.
Reviewed on Was this review helpful to you? Yes / No

Avatar
Wylie
Member

VERIFIED OWNER
  • JoinedMay 2013
  • Posts 5920
  • Reviews 78
  • Kudos3848
Overall   (4.0)
› Quality
› Value
0 of 1 people found the following review helpful
PROS
Stainless steel Glass Dual wick capability Reduced chamber Hole for drip tip is the right size! Many drip tips fit very well, better than most at least. Solid construction. Wick hole size. Less need for lower ohms builds with reduced chamber. 22mm diameter matches many devices. Wide open build area with pos post removed. Good surface area contact with supplied screws, works well with ribbon type coil wires.
CONS
Single wick builds need the extra hole in cap plugged or it weeps liquid. Tanks glass can slide on the o-rings if you're not careful, not as bad with the cap on though. Would prefer a larger tank, 4+ ml, just a personal preference. Drip tip is a bit short for me and brings your lips to the heated cap, personal preference again. No screws for dual wick builds!
So far these are likely the best genesis style atomizers I have. I haven't built any in dual wick mode yet as I have dedicated dual wick genesis tanks and they go through a lot of e-liquid, besides the fact this didn't come with the screws needed for a dual wick build! Flavor in the reduced chamber is better than without a reduced chamber although with the reduced chamber it is easier to build wick and coils get flooded. These do need a bit more attention in screwing off and onto devices being the glass tank section will turn easily while not turning the 510. Once the cap is removed be careful with this glass section as it can be pulled off easily resulting in an e-liquid spill. I have one mounted on a K103 and it looks almost hybrid, too bad 18350s don't last any longer than they do!
Reviewed on Was this review helpful to you? Yes / No

Avatar
Wylie
Member

VERIFIED OWNER
  • JoinedMay 2013
  • Posts 5920
  • Reviews 78
  • Kudos3848
Overall   (3.2)
› Quality
› Value
0 of 1 people found the following review helpful
PROS
same
CONS
Small fasteners on positive post
Was just rebuilding and realized the positive connections don't come with washers like I added to another I built previously. Brain fart!
Reviewed on Was this review helpful to you? Yes / No

Avatar
Wylie
Member

VERIFIED OWNER
  • JoinedMay 2013
  • Posts 5920
  • Reviews 78
  • Kudos3848
Overall   (3.5)
› Quality
› Value
0 of 1 people found the following review helpful
PROS
Stainless and Glass Dual wick ability Wick hole size Decent capacity Positive pin insulator of harder than usual material, big plus! Decent sized fasteners more applicable to ribbon and twisted coil wires.
CONS
No well in build area to retain over filling or bed silica for dripping or wicking of excess liquid. Cap could be tighter Lack of a drip tip.
One out of the five I have ordered showed up missing the upper tank o-ring and had slightly chipped glass. Although not straight across from each other dual wick with vent hole is possible by removing the raised negative connection which I have never used anyway. The cap is slightly loose, not terrible but looser than I would like, simple o-ring swap, no big deal. I have opened up the air inlet in the cap although I don't know what size it is, I use pointed diamond coated dremel tools for this and open the holes a little than test, open the hole a little than test... I like the positive pin insulator and wish more products would change to this type, have been seeing more lately which is good! I'm a genny fan and these are reasonably priced decent gennies.
Reviewed on Was this review helpful to you? Yes / No

Avatar
Wylie
Member

VERIFIED OWNER
  • JoinedMay 2013
  • Posts 5920
  • Reviews 78
  • Kudos3848
Overall   (2.7)
› Quality
› Value
0 of 1 people found the following review helpful
PROS
It works Very compact Locking button 510/eGo threading
CONS
Tubes threads are going to wear fast, real soft aluminum. Spring isn't very strong in the button Battery length dependent fit and finish, caps fitting flush with various batteries may not happen.
It's $6 mech, I swapped out the center pin and now Efest 14500 IMRs fit. Before the center pin swap there was a gap at the cap. Decent little mech for my BFT. I bought two and I'm not sure what I'm doing with the other one yet. Probably a back up beater for work I guess.
Reviewed on Was this review helpful to you? Yes / No